Why Veken Pet Fountain flashes red light? [Solution] 2022 (2023)

spread the love

Last updated on November 3, 2022

If you have oneVeken Trinkbrunnen shines rotten, this could mean that it needs to be cleaned. Follow the steps below to clean your Veken Drinker.

Why Veken Pet Fountain flashes red light? [Solution] 2022 (1)

Remove the pump from the base of the pump assembly located at the bottom of the water storage tank. Place in a bowl or rinse with warm (not boiling) water.

Thoroughly rinse all parts of your fountain, paying special attention to frequency filters or other easily removable parts such as spray nozzles or flow control valves. If necessary, use a toothbrush to remove any debris trapped in crevices and crevices in these areas.

This article will give you all the information you need to enjoy your new device for years to come.Veken cat water fountain flashes red!

(Video) Cat Water Fountain pump fix

What does the flashing red light on the Veken water dispenser mean?

Let everything dry completely before putting it back together. This is a common problem that occurs when the water fountain stops working. The best way to get rid of it is to clean the source well and dry it thoroughly.

Why Veken Pet Fountain flashes red light? [Solution] 2022 (2)
buy on amazonCompre no Walmart

If you notice this blinking light, there are several possible reasons:

  • The water flow can be set too high or too low depending on your pet's needs. In this case, open the spout cover and place it in the correct position.
  • You may have put too much water in the container. This can be caused by many factors such as too much salt or sugar in your pet's diet, but you can check this by checking to see if any liquid comes out when you put some water in it.
  • There may be something wrong with the filter as it has some dirt after cleaning all of the above issues

Why is my Veken water dispenser flashing red?

If the red light on your veken pet fountain is flashing, it means there is a problem with the pump or the pet fountain. When you see the flashing red light on yourVeken pet fontand you think it's just a minor problem, you should probably call customer service.

The good news is that this is not very likely unless there is a problem with the pump or the fountain itself. Most of the time, a flashing red light means something is wrong with one of these two things, but how can you tell?

(Video) How to Fix and Clean Cat Flower Fountain|Water Pump not working #catslifeph #waterfountain

  1. The pump is not working properly

If your Veken waterer is flashing a red light and nothing else seems wrong, there is probably something wrong with your pump. It may be necessary to replace this part if it is broken or damaged in any way. In that case, the flashing red light will go out as soon as you install a new one.

  1. The filter needs to be cleaned

The main filter is the most important part of your veken water cooler. This is where all the water is filtered and then flows to the rest of the unit. If this part is not clean, it will cause problems when trying to fill it with water.

This can also cause algae to grow in your pet's water bowl, which can cause nausea. You may see dirt or debris on top of this filter, but if it's been sitting around for a while and you don't want to clean it right away, just use a toothbrush and warm water to scrub away any residue.

  1. The pump needs to be cleaned.

The pump that powers your Veken pet fountain is usually responsible for pushing all of the water through the indoor plumbing system, including the filter and ball valve, and all of the piping that connects everything in your unit.

If any of these components become clogged, water will be prevented from flowing properly through all of these parts; In this case, your source will stop working until you solve the problem that was causing these components to clog.

  1. The ball valve must be cleaned

If you find debris trapped in the ball valve, clean it immediately to prevent the source from malfunctioning. If so, you may have to replace it with a new one and pay a little more than usual for these repairs.

However, if your source is working fine and you don't want to spend more money buying new parts, you can try cleaning the ball valve yourself using a water and vinegar solution and vigorously scrubbing until all the dirt comes out.

  1. The timer needs to be reset

Most dog waterers have a sensor that detects when the water is running. This sensor is activated by an electronic timer that runs on batteries or electricity. When that timer reaches zero, it shuts off all power to the pump motor and no longer produces fresh water for your pet's fountain. If this happens, simply reset the timer by pressing it until it clicks to reset it and start making fresh water again!

(Video) Our Point of View on Veken Automatic Pet Water Fountains

How to fix Veken pet font flashing red?

If your Veken water dispenser is flashing red, this could be a sign that the water filter is no longer working. This is not a problem with the font itself and should be fixed ASAP.

If you're looking for ways to fix the blinking red light on your Veken fountain, here are some of the top options:

  1. Check the filter cartridge

If you see a lot of debris in the water and it's still flashing red, it could mean your filter cartridge needs to be replaced. To do this, remove the filter cartridge from its base and check for dirt or debris underneath.

You can also use an old toothbrush to remove any dirt or debris trapped between the holes. If these methods still don't remove the residue, it means your filters need to be replaced, and you can find replacement cartridges at most pet or online retailers.

  1. Clean the pump and hose

clean yourPumpcasing and make sure that all parts move freely inside. This includes all cables that connect directly to it, as well as any piping that connects them. If any parts are stuck in the filter pump.

  1. Turn off pump power

Se você tiver um temporizador definido em sua bomba, verifique se ele está desligado. Isso evitará que a sujeira se acumule na bomba e cause problemas posteriormente.

  1. check the filter

The filter should be changed regularly as over time it can become clogged with dirt and debris that can cause problems with the pump later on. Check the filter now and clean it if necessary so you don't run into problems after what at first appeared to be a problem with the source not working properly.

Troubleshooting steps for Veken font flashing red

Step 1:Make sure the battery is fully charged. The flashing red light on the fountain will turn off when the battery is fully charged.

(Video) How to repair a CatMate/PetMate 33501 water pump

Step 2:Check if there is water in the well. If you see water or condensation on top of the fountain, let it dry for 24 hours before using it again.

Stage 3:Check for dirt trapped in any of the spouts or spouts on the fountain. If so, remove it with a small toothpick or toothpick and clean with warm water and soapy water (do not use alcohol).

Step 4:Check to see if there are any other clogged pipes in your home (faucet, toilet, shower, etc.) that are causing problems like this and could also cause water damage in your home. In that case, contact an experienced plumber immediately to fix the problem. After that, you can use your Veken font again without any problems!


Veken pet fountain is one of the most popular products for keeping pets happy and healthy. The reason is that it gives your pets a safe place to drink without worrying about falling or getting hurt. It also prevents them from drinking too much water, which can lead to dehydration.

When you have a new Veken waterer, you should know how to use it correctly and what to look out for when using it. Without proper care and maintenance, your Veken water cooler will not last long.

spread the love


Why is my pet water fountain blinking red? ›

Blue LED is ON: The water fountain works in interval mode. 3. Red LED is flashing: Lack of water, please fill in water in time.

Why did my pet fountain stop working? ›

Clean your pump

Oftentimes, if your fountain has reduced water flow or has stopped working, your pump simply needs to be disassembled and thoroughly cleaned. Different fountains come with different pumps, however, the cleaning steps remain the same. We recommend cleaning the pump every 2-4 weeks.

Why has my Petkit water fountain stopped working? ›

What should I do if the Smart Drinking Fountain's water pump is not working? Please take apart the water pump and clean out the debris inside. Wipe it with a paper towel and reassembled the parts again. Once the impeller is clean without any stuck debris, the pump will start working normally.

How often should I change the filter in my pet fountain? ›

How often should I change the filter? The charcoal filter should be changed every 2 to 4 weeks, depending on the number of pets using the fountain. If you have more pets or notice more debris, a slimy feel, or decreased water flow in your fountain, you should clean it more often.

How do you restart a fountain? ›

Open the pump cover, ensure there is not any buildup on the interworks of the pump or debris on the impeller. Gently clean the impeller with warm water and a soft bristled brush. If you need any additional help evaluating your pump's performance, contact Customer Care.

Why does my fountain pump keep stopping? ›

Clear any debris and then try turning it back on, it may restart. Overheating can be caused by clogged strainers or dirt building up in/around the pump. A thorough clean will often help. Overheating also results from wear and tear, or scale building up on the rotor and bearings.

Should you leave fountain on all the time? ›

Should I Leave My Fountain on All the Time? Fountain pumps are specifically designed to run constantly. It is hard on the pump if you constantly turn it on and off every day. The only times you should turn off the fountain pump is if you are cleaning it or if you are going to be away from it for several days.

How long do pet fountain pumps last? ›

The pump can be used for 1.5-2 years. We found that 99% of the pumps can be reused after cleaning by analyzing the returned products from customers.

How do I reset my Petkit water fountain? ›

Before replacing the filter, turn the PETKIT Eversweet Gen 3 Smart Drinking Pet Fountain off. After changing the filter, reset the drinking fountain by simply holding the black button for five seconds.

How do I reset my Petkit fountain? ›

Before using the filter, soak the filter for about 2 mins twice by putting the filter onto the pallet. After replacing the filter, press and hold the reset button for 5s to make the orange light disappear.

How do you troubleshoot a water fountain? ›

Clogs are the number one reason drinking fountains don't work. Look at the bubbler (where the water comes out of) and see if there are any obstructions. Sometimes dirt or other gunk gets stuck making drinking from the fountain impossible. Use a sharp stick to see if the system has been clogged.

Should you run a fountain pump 24 hours a day? ›

DOES MY FOUNTAIN NEED TO BE RUNNING ALL THE TIME? There are advantages to leaving your pump running all the time although it is not required. Leaving the pump running cuts down the wear and tear on the pump from starting and stopping, and therefore increases the life of the pump.

Can you use pet fountains without filters? ›

All cat fountains will run without the filters. They do not assist in the mechanics of running the fountains. However, if the fountain has a lot of nooks and crevices in which debris can collect it will definitely want some sort of mechanical filtration to prevent this material from entering the pump.

Can I put vinegar in my fountain? ›

Add Vinegar To Your Fountain

To quickly clean and freshen your indoor water fountain, add a cup or two of filtered white apple cider vinegar. Vinegar exhibits antibacterial, antiviral and antiseptic properties, killing germs on contact. And best of all, it's all-natural and doesn't rely on the use of harsh chemicals.

Will vinegar damage my fountain pump? ›

Vinegar does not hurt your fountain pump! There is nothing left to worry about if you decide to use vinegar. You can remove stains and discoloration easily. The basic idea behind cleaning most water fountains is understanding the system inside and knowing how to clean.

Can an LED light be repaired? ›

A great benefit to LED bulbs is you can repair almost everything. Premature burnouts can be caused by poor component quality, LED overheating, and voltage jumps. The good news is that you don't have to have a lot of experience to handle the repair and the cost is significantly less than the price of a new bulb.

Why are my LED lights malfunctioning? ›

Reasons often include a faulty power supply, loose connections, a faulty circuit design, or even damage due to water ingress caused by rain. Whatever the reason is for your LED lights not working and whatever the tell-tale signs are, there's usually a solution to the issue.

Why are my LED lights acting weird? ›

The most common cause of flickering LED lights is a poorly matched LED power supply, otherwise known as a LED driver. LED lights either require a constant current LED driver or constant voltage LED driver. There is no hard and fast rule as to what type of input certain types of LED lights require.

What is the reason if pump starts and stops too often? ›

If the water supply pipes become clogged, the pump will short cycle. A clog in the water supply creates high water pressure very quickly. The best way to check for this is to check the water filter. If it's dirty or blocked, replace it, and you may restore function.

What is the most common reason for pump failure? ›

The most common is improper lubrication when the incorrect lubricant is used or not enough is applied. Bearings also fail in extreme temperatures. Another cause of failure is bearing overload, e.g., a pump cavitating from lacking the proper flow will increase pressure on the impeller's front.

How do I stop my pump from short cycling? ›

What You Can do to Prevent Excessive Cycling on Your Water Pump
  1. Repair the tank air volume control.
  2. Drain the water tank and let air re-enter the tank.
  3. Drain the water from the tank and use the air inlet valve to recharge air back into your tank. The air charge should be 2 psi lower than you pump cut-on pressure.

How often should you clean a pet fountain? ›

The fountain should be cleaned at least once a month to avoid mineral buildup and to ensure clean drinking water for your pet. It is recommended to clean the pump and change the filter when cleaning the fountain. Multi-pet households may need to clean every two weeks.

Do water fountains require maintenance? ›

To protect your water fountain investment, regular water fountain maintenance is required to prevent algae, water stains and blocked pipes from ruining the fountain's look and function.

Should you turn water fountain off at night? ›

While each unit is designed to be left switched on 24/7 if you want them to be, it's not energy-efficient to do so. To help you save money, you should switch the dispenser off at night to save electricity.

What happens if a fountain pump runs dry? ›

This will cause damage to the impeller and may cause the shaft to break from the impeller bouncing on it.

Do fountain pumps need to run continuously? ›

Running your fountain pump non-stop is the best way to keep your pond in good health. The constant circulation of water keeps the water clean and fresh and protects the flora and fauna that live in and around the water. The following are some of the top reasons to keep the pump running continuously.

Can a fountain pump run dry? ›

Dry running of the pump can damage the mechanical seal and the motor. For this reason, the float switches should be arranged so that the fill level in the shaft does not fall below the minimum level required to operate the pump.

How often should you change the water in a cat fountain? ›

If you use a fountain to keep your pet hydrated, make sure to clean it at least once a week and regularly replace the fountain filters. Make sure to keep your furry family member happy and healthy by providing him with daily fresh water and a clean water bowl.

How do you reset a Petkit filter? ›

After filter replacement, you need to press and hold the button for 5 seconds to reset filter light .

Can you leave a cat water fountain plugged in all the time? ›

The fountain should be remained plugged in 24/7 to provide your pet with fresh water. Only unplug the fountain to clean.

Does Petkit work without WiFi? ›

If the Smart Pet Feeder keeps disconnecting from your WiFi, the device will still dispense food, even if it is offline. However, you will not receive notifications and the PETKIT App will show that feeding has failed. If there is no other issue, the device will be back online automatically.

Is baking soda Good for fountains? ›

A solution of distilled white vinegar and water can vey very helpful in cleaning the fountain surface. If you have a tough spot of scale that doesn't want to budge, make a paste of baking soda and water and let it sit in there a bit.

How do you clean a clogged fountain? ›

You can use a homemade solution of distilled white vinegar mixed with water (50/50) to clean the pump. Simply remove the pump from the fountain and soak it in a plastic bucket containing the solution until the mineral stains dislodge. You can then wipe the fountain pump clean with a soft cloth.

Why has my water feature stopped working? ›

One of the main reasons that your fountain will stop, is because it needs to be cleaned. All pumps whether they are solar or not have to be maintained. Ponds are organic and the water always contains fine particles of sand or dirt, algae, pond weed, sediment and any number of other small pieces debris.

Do fountains use a lot of electricity? ›

Most fountains use around the same amount of energy as a small lamp, and you should not notice any significant increase in your electricity bill after installing your fountain. In addition, some outdoor fountains can be constructed to run on solar power.

How many gallons does a fountain use per hour? ›

To create a nice "average" looking waterfall or stream, it takes 1,800 gallons per hour (30 gallons per minute) for every 1 foot of width. To determine the GPH/GPM needed for your waterfall or stream - multiply the width in feet x 30 GPM.

How many hours a day should I run my fountain? ›

Downtime allows your mechanical devise to come to rest, prolonging the units' lifespan under normal use conditions. Our suggestion is to operate pond fountains for 12 to 14 hours per day in order to accomplish the necessary aeration of the water while greatly prolonging the life of the equipment.

Why is my cat fountain blinking red? ›

Blue LED is ON: The water fountain works in interval mode. 3. Red LED is flashing: Lack of water, please fill in water in time.

Can I use vinegar to clean my cat water fountain? ›

Just pour enough vinegar into the fountain to cover the scaly buildup. Place the fountain away from your cats until all is dissolved. Then wash well, and your kitties will have a squeaky-clean, buildup-free water fountain once again.

How long do pet water fountain filters last? ›

Maintaining your pet water fountain

Be sure to change out the water fountain filters per the instruction manual. Some filters need to be changed every 2-4 weeks, while others only need to be changed every 1-3 months.

How do you keep algae free in a fountain? ›

Using distilled water in your water fountain will help reduce the amount of algae that grows due to the water being more pure. Distilled water has the sediments and minerals removed, which helps reduce mineral buildup and algae growth.

Why do pet water fountains get slimy? ›

Pet fountain slime comes from biofilm development, or pet saliva, or a combination of both. Saliva breaks down food particles into simple sugars that are easier for animals to digest and absorb. Bacteria love sugar, too, and when they get a lot of sugar to feed on, they multiply very fast.

Why does my dogs water turn red? ›

Pink stains are most frequently observed in sinks, toilet bowls, shower stalls and bathtub enclosures and on showerheads, shower curtains, tile and in pet water bowls. They are caused by Serratia marcescens, an airborne bacterium.

What does a red light mean on a Elkay water fountain? ›

The Elkay filter status red means that the filter inside the units has either used 100% of its life or has been in use for over 12 months and that the unit is no longer providing users with filtered water.

How do you reset a cat's fountain filter? ›

Before using the filter, soak the filter for about 2 mins twice by putting the filter onto the pallet. After replacing the filter, press and hold the reset button for 5s to make the orange light disappear.

Why does my cats water fountain turn pink? ›

Believe it or not, the Attack of the Pink Slime is actually quite common, and is caused by a combination of airborne bacteria (called Serratia marcescens), mold, and yeast spores that thrive in damp environments.

What color is the fluid when a dog's water breaks? ›

Your dog's waters may break, which will be seen as clear fluid. In normal labour, your dog may show weak and infrequent straining for up to 2 hours (or at the most 4 hours) before giving birth to her first puppy.

What does it mean when the water is red? ›

Iron tends to add a rusty, reddish-brown (or sometimes yellow) color to water. If the color is more black than red, your water might contain a combination of iron and manganese. Both of these metals can cause staining of plumbing fixtures or laundry, but they are not known to cause health problems.

What are the signs of a water infection in dogs? ›

Dribbling of urine/loss of bladder control — often seen as accidents in the house. Blood in the urine. A strong smell to the urine. Pain on urinating — straining and sometimes even crying out.

What does red light mean on water filter? ›

The Filter light turns red to let you know when it is time to change your water filter cartridge. To give you time to get a new filter the red light comes on just before the capacity of the current filter runs out.

How do I reset the red light on my Elkay bottle filler? ›

Reset the Filter Status Light
  1. Remove the top cover of the bottle filling station by unscrewing the two Torx screws.
  2. Depress the program button for approximately two seconds until the display changes and then release.
Nov 18, 2022

Is it safe to drink water with a red filter status? ›

Ashley Boak filling up her Hydro Flask knowing that the water at red fountain is safe to drink. The Elkay water bottle filler stations have been popular throughout DGS ever since they were first installed about four years ago.

Can you leave a cat water fountain on all the time? ›

Pet water fountains are safe to use as long as you keep up maintenance. Check the water level daily to ensure your pet has access to fresh water, and because if the fountain ever completely empties, there's a chance it will burn out.

Why is my water fountain not working? ›

Clogs are the number one reason drinking fountains don't work. Look at the bubbler (where the water comes out of) and see if there are any obstructions. Sometimes dirt or other gunk gets stuck making drinking from the fountain impossible. Use a sharp stick to see if the system has been clogged.

Is pink mold harmful to cats? ›

Biofilm can cause life-threatening conditions when ingested or inhaled by pets or humans, and can contain: Serratia marcescens (the pink film you see in bowls, shower curtains, and other wet areas)

Can I use tap water for cat fountain? ›

While it's not the healthiest option, tap water is perfectly fine for most cats. In fact, many cats actually prefer the taste of tap water to filtered water. This usually does not come in a plastic bottle.

Can I use vinegar to clean cat fountain? ›

Clean all parts of the pump using soap and warm water with a small brush. Completely rinse the pump, then reassemble. If hard water build up occurs, soak pump in equal parts vinegar and warm water for 15 minutes, then scrub.


1. [Review] VEKEN-double decker pet drinking fountain
(Joel Homie Show)
2. How to setup cat water fountain by PetKomfy
(Pet Komfy)
3. Pet Water Fountain
(Anne Brown)
4. WOPET Cat Water Fountain
(Consumer Quest)
5. How To Clean the LamYoo Cat Fountain Water Dish
6. How To Clean The Wonder Creature Stainless Steel Top Pet Fountain
Top Articles
Latest Posts
Article information

Author: Gov. Deandrea McKenzie

Last Updated: 05/03/2023

Views: 5914

Rating: 4.6 / 5 (46 voted)

Reviews: 93% of readers found this page helpful

Author information

Name: Gov. Deandrea McKenzie

Birthday: 2001-01-17

Address: Suite 769 2454 Marsha Coves, Debbieton, MS 95002

Phone: +813077629322

Job: Real-Estate Executive

Hobby: Archery, Metal detecting, Kitesurfing, Genealogy, Kitesurfing, Calligraphy, Roller skating

Introduction: My name is Gov. Deandrea McKenzie, I am a spotless, clean, glamorous, sparkling, adventurous, nice, brainy person who loves writing and wants to share my knowledge and understanding with you.